Double distillation apparatus 18/300/t with CLAMP 1,5 inches for heating element в Челябинске по цене от 18640 руб

The traditional process for the purification of alcoholic beverages involves double distillation. After the first distillation of the mash in the receiving liquid, there is moonshine with some taste and smell from the feedstock. In addition, it contains a bouquet of fusel oils, ethers and a host of other volatile substances. Therefore, fractional separation is used, separating alcohol from impurities during the second distillation. The Chelyabinsk Distillation Apparatus Plant has prepared a solution in which double distillation is performed in one working cycle.

How the apparatus "Gorilych" of double distillation 18/300/t works with an active cooling tsar (reflux condenser)

Structurally, the steam cube consists of two successive circuits, where one distillation is immediately followed by the second. The only thing that needs to be done is to separate the low-boiling fractions with impurities - the so-called "heads" at the beginning of the distillation process into a separate container. This is not difficult, they will go first and have a pungent smell of solvent. After that, the moonshine still with an active cooling tsar will begin to produce clean and strong moonshine of a high degree of purity.

It is recommended to fill the tsarga of the primary circuit with a regular Panchenkov wire nozzle or ceramic Rashig rings, on which the process of separating the evaporating liquid into alcohol and other fractions is most efficient. Due to the fact that the device has two distillation chambers, two drawers - double purification of moonshine occurs in one technological process. At the same time, there is no need to control the appearance of tails - when the strength of the resulting drink drops, the liquid stops flowing from the apparatus. In the receiving vessel, crystal clear moonshine will remain, in the moonshine still - tails and bard.

Reasons for buying a double distillation apparatus

For 99% of the population, making high-quality home-made moonshine is a hobby. Most home distillers use sugar as a raw material, since it is available in any store, the technology for preparing sugar mash is also extremely simple. But many also prefer to use thick, fragrant mash. For such connoisseurs of the original flavoring component, an internal groove is provided in the distillation cube for quick and easy installation of a false door with a diameter of 300 mm in order to avoid burning of the mash. Moonshine still "Gorilych" double distillation 18/300/t for the installation of heating elements allows to reduce the heating time by installing a heating element directly into the still. For this, in the lower part of the distillation cube, a 2-inch KLAMP-type mounting flange is already installed in the basic configuration for installing the heating element, which is closed the rest of the time with a plug and a clamp that come with the kit.

For a person with a family and a steady job, time is often the most valuable resource. Therefore, if the moonshine is cleaned without human intervention in less time, it may be worth updating the fleet of home equipment. The presented model has an optimal volume of 18 liters, it has a low weight, it is not difficult to wash and collect, and a drain ball valve is installed in the distillation still for safe drainage of the stillage remaining after the end of the distillation process.

If you need to get alcohol at home with a minimum content of foreign impurities, while in just one working cycle, then a new moonshine still would be an excellent choice; you can buy it directly on our website.

Tags: distiller, moonshine, 18 liters, neck 300 mm, with thermometer, double distillation, for heating elements

DIMENSIONS (in initial configuration)

The lower compartment / upper compartment 14 liters/4 liters

Volume of the distillation cube, l 18

The diameter of the throat, mm 300

SPECIFICATIONS

Maximum productivity, l/h 0,8

Material Stainless steel

Maximum strength of the drink, % 80

Country of Origin Россия

Warranty of the factory 1 year

The height of the assembly, cm 67

EQUIPMENT (without additional options)

Clamp connection 1,5 inches

Diopter no

Drain cock there is

Induction bottom, mm 5

Installation for heating elements clamp 2 inch

Reflux condenser there is

Safety valve no

Selection node no

Set of silicone gaskets there is

Steam drum there is

Thermometer, pcs 1

Cooler Turbofan

Steam-dome Built-in

Ethanol level device no

Hoses for water supply no

The faucet’s adapter for the hose no

The product’s passport/documentation there is

Packing box there is

Reviews (0)

There are no reviews for this product.

Unpack the double distillation unit (ADP) and remove all packaging materials.
Remains of traces of factory treatment should be removed with water and detergent and rinsed with clean water.
Fill the distillation cube with a small amount of clean water, collect the ADP, installing the cooler (and the seals, if provided for the assembly) and connecting the hoses to supply water for cooling, boil (distilled) for 30 minutes. To disassemble the ADP, drain the remaining water from the distillation cube and cooler.
For a model with a 10 liter distillation cube, the volume of the primary wort should not exceed 8 liters. For a model with a 20 liter distillation cube, the primary wort volume should not exceed 16 liters. Use a clarified primary wort, pre-filtering it from the slurries of the fermentation products.
Primary wort is poured through the neck into the bottom compartment of the still.
In the upper compartment of the distillation cube, do not pour anything; During the distillation process in the upper compartment of the distillation cube and without it enough liquid is mixed to mix with moonshine after the first circuit and this is quite enough to reduce the level of molecular bonds before the uptake into the second circuit.
The recommended volume content of alcohol in the original wort is from 10% and above.
If Panchenkov's tap changer or other fillers are used (in ADP models equipped with drawers), then only the tsar of the primary circuit is filled. The second tsarga remains empty and works on the principle of film reinforcement.
Connect the cooling hoses to the fittings of the two-circuit cooler (and to the fittings of the active cooling side, if provided by the package) and check their connections for leaks by briefly supplying water to the hoses.
The ADP is placed on the heat source and the heating power is set to the maximum value (in order to shorten the heating time of the distillation cube)
When the temperature reaches 70°C on the thermometer, the water supply for cooling is turned on. Strongly not necessary, enough laminar flow of water (without air bubbles)
Upon reaching the values on the thermometer 75-80°C (the spread is due to the different strength of the primary wort and the measurement error), low-boiling fractions (heads) will begin to distill. Approximately 1-2% of the volume of the primary wort is selected (if the primary wort is sucrose) or 2-3% (if the primary wort is fructose).
Then the "body" collection begins. Do not forget to use a silicone tube to collect the product, in order to avoid unnecessary evaporation of alcohol into the air during collection.
As the alcohol content in the primary wort decreases, the thermometer readings will begin to rise, down to 99°C - these are the regulatory indicators.
If the alcohol content in the brew is lower than the critical value, the distillation process slows down automatically. This is expressed in the practical termination of the product's cap- blester.
Watch the thermometer. If the reading exceeds 100°C, turn off the heating source and wait for the ADP to cool down, disassemble the double distillation unit to perform a revision to find clogging of the connecting tubes.

Routine indicators:

For the ADP with a 10 liter distillation cube: approximately 1.2 liters of the finished product (in terms of 80% volumetric alcohol content) for 4-5 hours in a full cycle *
For ADP with a 20 liter distillation cube: approximately 2.6 liters of finished product (in terms of 80% volumetric alcohol content) for 6-7 hours in a full cycle *
For ADP with a 30 liter distillation cube: approximately 2.6 liters of finished product (in terms of 80% volumetric alcohol content) for 7-8 hours in a full cycle *

* Regulatory indicators may vary depending on the composition and "strength" of the original wort, the type and indicators of the power of the heating source, the temperature and intensity of cooling, temperature regimes, the type and density of fillers used for the king.

Delivery of Gorilych products and related products.

You can buy any stills, brewing and distillation column "Gorilych" in our Internet-shop ChZDA and get your order in Chelyabinsk or in official representative offices in different Russian cities. The list of stores or points of delivery (PWZ) in the Chelyabinsk region is constantly expanding and the actual information on their addresses and office hours you can always find on the interactive map when ordering, or get the information you need from our consultants free by phone 8 (800) 775-90-83.

You choose your own delivery variant.

You can choose a convenient way of delivery of your stills "Gorilych" and other CHZDA products to Chelyabinsk. When ordering, specify the type of delivery and select any delivery point (PWZ) in the list or on the interactive map. We will take care of the rest.

Safe and cautious packing

Before shipping your order each kit of Gorilych stills is carefully inspected for any external defects, wrapped in bubble wrap, carefully and tightly packed in shipping carton and provided with all the necessary documents (bill of lading, passport, warranty card). During the whole process of delivery to Chelyabinsk region we always track the location of your order to notify the buyer on the arrival of the goods to receive them.

Up-to-date information on the location of the order

Due to advanced integration solutions in Chelyabinsk ZDA online store the buyer is always aware of where and at what stage his order is.

Online information in the personal cabinet about the order's progress at all stages;

convenient services on site to track the progress of the order;

Post and SMS-notification of changes in order status and readiness of goods for delivery;

Agreeing on a convenient time of delivery with the courier service.

Look first, pay later

Due to our courier service and long-term cooperation with reliable transportation companies, the customer in most cases (excluding Russian Post) can always open the package upon receipt of the order and make sure that the package is intact and the order is complete. And only if there are no comments, the buyer can pay for the received goods in the store, at the point of delivery or to the courier.

ChZDA store not only offers quality stills and distillers of its own production in Chelyabinsk region, but also the most comfortable, and most importantly, favorable conditions for the purchase in Chelyabinsk. You do not need to solve the question of payment when ordering products from our catalog because you can pay for the stillizer in any convenient way including:

Bank cards MIR, Visa, Mastercard, Maestro;

Payment through a bank branch;

Through a system of electronic money UMoneu;

Payment to the courier at delivery of the order;

Payment at the issuing point;

Payment by cash on delivery at the post office;

We also have unique ways of payment - by accumulated bonuses and a gift certificate. Take part in our promotional actions, accumulate bonus points and get our products with great discount.

Absolute protection for online payments

All payments for CHZDA goods are made online through secure service JuMoneu, so you can be sure that all information with payment data is guaranteed to remain confidential and secure and can not be used by unauthorized persons: payment service JuMoneu is protected by PCI DSS - a standard Visa and Mastercard. Payments are credited on the same day.

We wish you successful purchases!